Multifunction-PLC-IO-Module with USB and RS232

• 4 digital inputs and 4 digital outputs
• All in- and outputs are electrically isolated and working with 12 – 24 VDC
• Communication over USB and RS232
• RS232 can be used over USB as a tunneled connection
• PCB size is 72x42.5 [mm]
• Available with D-SUB 15 HD connector
• Plug & Play with EyeVision 3
• Power supply over Mini-USB connector

Assistance system Allviss
For support at various manual workstations for zero-defect production.
The assistance system displays work steps and immediately identifies errors and is thus optimally suited as an inspection system against production errors. This is feasible due to the powerful image processing software of EVT GmbH, which is used for this purpose.

Allviss is also available in different variations as Advanced or with Deep Learning.

Product for pickup or shipping by arrangement.

Crosshair generator with image processing software; EyeVision software.

The crosshair generator, comes complete with compact computer and camera with standard C-mount connection
which fits to all standard optics,
A monitor can be connected to the system via HDMI cable, which then displays the image and the
the crosshairs are displayed. For the crosshairs different options can be selected
from simple crosshairs to different lines and circles, which can be switched on and off individually.
switched on and off. The system also makes it possible to define a measuring range, if a change in brightness should
a change in brightness takes place, a signal can be triggered, so that automatic
measurements can be triggered.
There are several options that can be purchased with the crosshair generator, which makes it possible to
it is then possible to carry out measurements in the image field of the crosshairs.

Shipping is calculated individually depending on the scope and carrier and is to be borne by the buyer.

Multifunction-PLC-IO-Module with USB and RS232

• Available with screw terminals
• 4 digital inputs and 4 digital outputs
• All in- and outputs are electrically isolated and working with 12 – 24 VDC
• Communication over USB and RS232
• RS232 can be used over USB as a tunneled connection
• PCB size is 72x42.5 [mm]
• Plug & Play with EyeVision 3
• Power supply over Mini-USB connector

Easily inspect and control profiles with the EyeCon profile

Instant license plate reader based on Eyevision image processing software with AI.

Automatic recognition and reading of license plates.
Due to Deep Learning component also possible under bad conditions.
Fields of application are e.g. parking garages and traffic monitoring.

System to read license plates in small parking areas or access restrictions, and compare with a positive list and allow access.
The system is supplied completely ready for use, the Ethernet interface can be used to transmit the positive list or a valid license plate, so that the system can activate a switching output when it detects one of the license plates.
The system is designed to recognize 1 license plate per second, faster systems are optionally available.
With the recognition performance of 1 license plate per second, it is easy to implement barrier systems. Since the product is based on the EyeVision image processing software, it can be flexibly expanded with additional functions at any time.

Technical data:

Evaluation unit:

Processor: 4 Core with 1.6 GHz

Working memory: 1 GByte (optionally 4 or 8)

SSD: 32 GByte (optionally 256 GByte)

Monitor connection: HDMI

Connection: 2 x USB 3

Switching output: 1 x 24V (Optional 2 outputs and 1 input)

Camera connection: CSI

Camera resolution: 8 MPixel

Software: NP reader

Shipping will be charged individually depending on the volume and carrier and is the responsibility of the buyer.

(price on request)

Technical Data:

• 3D Technology: PMD Time of Flight (19k-S3)
• Pixel: 160 x 120
• DSP: BF561 (2 x 500 MHz)
• RAM: 32 Mbyte SD-RAM
• FLASH: up to 64 Mbyte NOR
• Frame Rate: up to 40 fps Range 3 – 5 m
• LED: 2 x 850 nm
• Power Supply: 24V @ 0.7 A
• Ethernet: 10/100 Mbit
• RS232: 1
• RS485: 1
• GPIO: 3
• Trigger: Input 1
• Temperature range Industrial: -40 bis +85 °C
• Cooling: Passive
• Dimensions: (B x H x T) 60 x 60 x 40 mm
   

(price on request)

Technical data:

• Sensor Vendor: Panasonic
• Resolution: 640 x 480 pixels
• Frame Rate: 20 fps
• Interface: Gigabit Ethernet-, GigE Vision- and GenICam-compliant
• Working Range: 0 m - 13 m
• Accuracy: +/- 1 cm (depending on tableau)
• Lens: 57°h x 43° v
• Operating System: Windows- and Linux-compliant
• Digital I/O: 1 In / 1 Out
• Operating temperature: 0°C – 50°C
• Weight: 0,4 kg
• Power: 24 V DC, 15 W

Precision-extruded aluminum profile to DIN 17615, warm hardened, surface anodized natural, smooth ends.
Suitable for substructures and mounting elements which are exposed to dynamic loads.

• Profile area: 1480 mm²
• Section modulus: Wx = Wy = 23 cm³
• Moment for inertia: Jx = Jy = 76 cm4
• Tolerance length DIN 7168
• Distortion tolerance 1 mm/m
• Straightness tolerance 0.5 mm/m
• Weight 3.996 kg/m

Precision-extruded aluminum profile to DIN 17615, warm
hardened, surface natural, smooth ends. Suitable for substructures and mounting elements which are not exposed to
dynamic loads.

• Profile area: 809 mm2
• Section modulus: Wx = Wy = 13 cm3
• Moment of inertia: Jx = Jy = 45 cm4
• Tolerance length DIN 7168
• Distortion tolerance: 1 mm/m
• Straightness tolerance: 0.5 mm/m
• Weight: 2.186 kg/m

Precision-extruded aluminum profile to DIN 17615, warm hardened, surface anodized natural, smooth ends. 3000 mm long.

• Profile area: 1767 mm2
• Section modulus: Wx = Wy = 37.82 cm3
• Moment of inertia: Jx = Jy = 181.53 cm4
• Tolerance length DIN 7168
• Distortion tolerance: 1 mm/m
• Straightness tolerance: 0.5 mm/m
• Gewicht: 4.771 kg/m

Precision-extruded aluminum profile to DIN 17615, warm hardened, surface anodized natural, smooth ends.

• Profile area: 368 mm2
• Section modulus: Wx = 1.025 cm3 / Wy = 1.640 cm3
• Moment of inertia: Jx = 0.820 cm4 / Jy = 3.280 cm4
• Tolerance length DIN 7168
• Distortion tolerance: 1 mm/m
• Straightness tolerance: 0.5 mm/m
• Weight: 0.980 kg/m

Precision-extruded aluminum profile to DIN 17615, warm hardened, anodized natural, smooth ends. Used for making adapters.

• Profile area: 271 mm2
• Section modulus: Wx = 0.32 cm3 / Wy = 1.36 cm3
• Moment of inertia: Jx = 0.14 cm4 / Jy = 2.72 cm4
• Tolerance length DIN 7168
• Distortion tolerance: 1 mm/m
• Straightness tolerance: 0.5 mm/m
• Weight: 0.732 kg/m

Precision-extruded aluminum profile to DIN 17615, warm hardened, anodized natural, smooth ends. Used for making adapters.

• Profile area: 600 mm2
• Section modulus: Wx = 1.04 cm3 / Wy = 4.83 cm3
• Moment of inertia: Jx = 0.67 cm4 / Jy = 13.53 cm4
• Tolerance length DIN 7168
• Distortion tolerance: 1 mm/m
• Straightness tolerance: 0.5 mm/m
• Weight: 1.620 kg/m

Precision-extruded aluminum profile to DIN 17615, warm
hardened, anodized natural. With T-slot for M5, M6 and M8
square nut (non slip with drop protection) of steel, chemically
nickel-plated.

• Section modulus:
  • Wx = 1.346 cm3
  • Wy = 1.7466 cm3
• Tolerance length: DIN 7168
• Weight: 0.8546 kg/m

Snap-on profile for routing pneumatic hoses and electric cables – aluminum, warm hardened, anodized natural, smooth ends.

• Tolerance length DIN 7168
• Weight: 0.549 kg/m